Gas Mask and Respirator Wiki
Register
Advertisement
Worker-128 Hold up! Under construction
This article or section is currently under construction and is in an unfinished state. If there is an urgent need for information about this topic, comment at the bottom of this page with a question.



The GM38 was used by the German Army in the Second World War and was created as an upgrade for the GM30. 

Overview

GM38

The facepiece was made entirely from rubber. The metal parts on this mask have a variety of colours, which represent why they were used. Masks with tan painted parts were used in the tropics of Africa in World War II as it is painted in 'sand colours'. The mask has a 5-pointed strap harness which is tightened with two straps in the mid-section and another two near the bottom. The mask was issued in a canister which was carried around the neck but the mask also has its own carrying strap with which it could be carried.

GM38 Luftwaffe

The Luftwaffe had an additional, lateral round thread connection, depending on the aircraft type, right or left, with corrugated hose or filter. Depending on requirements, the unneeded connection was sealed with a round threaded plug. These masks were not crew equipment but remained in the aircraft.

GM38 Funker/Mikrofon

Very rare variant. It had a removable metal cap on the side into which the microphone was screwed. It was issued for radio operators.

Filter

The mask was issued with many different filters varying on the users. The Civil Defence used it with S-Filter. The armed forces used various filters, mainly FE 37, FE 41 and FE 42. In general, all filters were round canister filters painted in green colors.

Markings:

  • FE: combat filter
  • Fe: ferrum (iron)
  • AL: aluminium
  • NM: not magnetic
  • R: Drinked Improved Ring-shaped Nebula Filter (In older filter-tops the R was stamped, in the newer ones) soaked = hexamethylenetetramine Refilled
  • HN: hexamethylenetetramine Refilled
  • Tp, Tr or Tropics: tropical filter

Carrying canister

The mask came in a round steel canister called Gasmaskenbüchse (gas mask canister). On the inside of the lid, there is a separated section for the anti-fog inserts.

The GM38 was issued with the fourth, tall, type canister. The other canisters remained service at the same time with GM30 masks, getting gradually replaced with newer canister as the war progressed.

First model Reichswehr and Wehrmacht canisters used between 1930-35 are around 26 cm high with a diameter of around 12 cm.

The second model used between 1935-36 is a bit shorter at 25 cm. The diameter remains the same. The closure system changed, adding a canvas pull strap for easier opening.

The third model used between 1936-38 has an updated closure system again, which remains the same for all following models. The dimensions are the same as the second model.

The fourth model (1938-45) keeps all the hardware features of the third, but is longer (around 27 cm) to better accommodate the rubber GM38 mask.

Early versions of the fourth and previous types are not waterproof, later variants however are. A waterproof canister is marked with a "D" for Dicht ((water)tight) on the bottom.

Service

Germany

Flag-de-wh Wehrmacht (Army of Nazi Germany)

Flag-de-ss Schutzstaffel (Nazi pary army)

Flag-de-bw Bundeswehr (German Army)

The GM30 was created as a successor to the GM24 and was issued to the Wehrmacht and to other branches in Nazi Germany, however never fully replaced the GM30. Later it was issued to the Bundeswehr till it was succeeded by the GM54.

The mask was used for protecting the user's face from the backblast of the rocket leaving the tube of the RPzB 54 Ofenrohr ("stove pipe" - early Panzerschreck without protecting shield).

In concentration camps like Auschwitz, the mask was used by the guards when dealing with Zyklon B, it required a special "J" filter.

Soldiers on the Eastern front would sometimes wear the gas mask without a filter as a mean of protection from the cold.

Denmark

Flag-civil-defence Civilforsvaret (Danish Civil Defence)

M/45T

Czechoslovakia

Flag-cs-ca Československá armáda (Czechoslovak Army)

The GM38 has been produced in Czechoslovakia since the time Germany annexed it by a company named Fatra (factory code "ebd"). After the fall of the reich, the production stopped. However, in late 1945, the production of the GM38, along with the Vz.35, has been restarted at the GuZu plant in Zubří, and ran until 1951. The gasmask, both newly produced and old german stock, entered service with the czech army in May 1945, under the name "Vz.38N" [Vzor 1938, Německá (german)]. The postwar production was virtually unchanged from the wartime ones, and can only be distinguished by the marking. Whilst in Czech service, the kit was identical to german ones, again, only distinguishable by the markings. The mask was made obsolete in 1952, when, during modernization, the Czech army got rid of all gasmasks that weren't 40mm GOST.

Gallery

German_GM-38_Gas_Mask

German GM-38 Gas Mask

References

Advertisement